Curriculum Sub-Committee at its meeting on 7 May 2009 recommended to Learning and Teaching Committee and Senate that approval be given to the following proposals. Details are available from the Secretary.
1. BSc (DPS/DIntS) Engineering Management: New Programme Proposals
.1 The Sub-Committee considered proposals
from Mechanical and Manufacturing Engineering for a new full-time programme
with effect from October 2010 entry. Concern was expressed about some common
teaching in Part A with the SEFS foundation programme, and with the inclusion
of A modules in Part B, C modules in Part B and particularly D modules in part
C. The programme did, however, conform to the University’s credit
framework, but the possibility that Part D students on extended programmes
could be taught together with Part C students on this programme was not felt to
be acceptable.
.2 It was noted that the award for the
programme was BSc rather than BEng, that accreditation was unlikely to be
sought, and that A-level Mathematics would not be an entry requirement to the
programme. The latter was likely to be influencing the timing of modules so
that students had the necessary mathematical background for some of the
engineering modules. The Sub-Committee was unclear, however, as to the intended
student market for the programme, the careers that its graduates were likely to
pursue and how industry would perceive these graduates. The programme appeared
to have been designed with a small management component to make it more
attractive to students who would be unlikely to be accepted onto BEng/MEng
programmes. This concern was echoed in the comments from the external assessor.
.3 It was AGREED to recommend the
proposals to Learning and Teaching Committee subject to the following matters
being resolved to the satisfaction of the AD(T) prior to the meeting of
Learning and Teaching Committee:
(a)
A statement should be provided of the students likely
to be recruited to the programme and the likely careers that graduates would
pursue.
(b)
The proposers should reflect on the wisdom of common
teaching with the SEFS programme. Foundation students moving to this programme
might find themselves having to repeat material they have already covered. If
common teaching was necessary there should be some differentiation in
assessment for the different student groups.
(c)
Programme Regulations
(i)
The proposers should: reflect on the mix of module
levels in each Part; explore ways to include MMA102 in Part A; and avoid the
use of D modules in Part C, perhaps by the use of appropriate C modules from
the
(ii)
(iii)
(d)
Programme Specification
(i)
(ii)
(iii)
(iv)
(e)
Module Specifications
(i)
Presentation of all the specifications required some
improvement.
(ii)
MMA110/111: More than one knowledge and understanding
ILO and at least one transferable skill would be expected. It was unclear
whether the 22 hours of effort for the module comprised both lectures and
tutorials. The 3-hour exam for MMA110 seemed excessive for a 10-credit module.
(iii)
MMB102: This module did not appear in the Programme
Regulations. Should its modular weight be 10 rather than 20?
(iv)
MMB610, MMA210, MMB102: Reference to timings in the
MTLA field should be removed.
2. MSc Signal Processing in Communication Systems: New Programme Proposals
The Sub-Committee considered
proposals from Electronic and Electrical Engineering for a new
full-time/part-time programme with effect from October 2009. The programme would provide an additional variant in
the suite of Digital Communication Systems postgraduate programmes. It was AGREED to recommend the proposals to
Learning and Teaching Committee subject to the following matters being resolved
to the satisfaction of the AD(T) prior to the meeting of Learning and Teaching
Committee:
(a)
Programme
Regulations
Delete
paras 3.2 and 3.4. This information should be included in module
specifications.
(b)
Programme
Specification
(i)
(ii)
(iii)
(iv)
(v)
(vi)
(vii)
The project work
would be expected to feature more in the Programme Specification as it appears
to be quite significant.
(c) Module Specifications
(i)
ELP012: Prerequisites
were not required as all modules were compulsory. ILO 2(i) was not a learning
outcome.
(ii)
All modules on
the programme should be checked for ILOs that were appropriately expressed.
(d)
Curriculum Map
(i) It
was surprising that T2 was only met by the project module; fortunately students
were required to pass this module.
(ii) A
Curriculum Map covering the suite of programmes was required.
(e) Assessment
Matrix
(i) There
appeared to be little variation in assessment across the modules, but may depend
on the type of case studies. Confirmation of this was required.
(ii) Assuming
that the 0.5 hour examination listed for the project was the viva, this should
not be appearing in the examination column.
(f) Consultation
Forms
The
awaited responses from the External Assessors were required, which should be
supportive.
3. MSc Information and Knowledge Management: Major Programme Changes
The Sub-Committee considered
major programme changes with effect from October 2009 entry.
The
changes involved a repackaging of existing material from 10-credit to 15-credit
modules so that the programme was consistent with other postgraduate programmes
in the department, and the withdrawal of modules taught jointly at UG and PG
level. It was AGREED to recommend the proposals to Learning and Teaching
Committee, subject to the following matters being resolved to the satisfaction
of the AD(T) prior to the meeting of Learning and Teaching Committee:
(a) Programme Regulations
(b) Programme Specification
(i)
(ii)
(iii)
(iv)
(c)
Module Specifications
(i)
ISP508:
Second aim to read ‘to introduce students to software packages that are
commonly used for web design’. Reference to field trip in feedback
section to be clarified.
(ii)
ISP509:
‘Academic essay’ in MTLA field to be clarified.
(d) Curriculum Map
Assessment
of knowledge and understanding outcomes appeared light, with the exception
of ISP487. The proposers should reflect
on this and whether, for example, the dissertation module included some
assessment of these outcomes.
4. MEng
Innovative Manufacturing Engineering: Proposed Additional Pathway to MEng
Innovative Manufacturing Technology
It was AGREED to recommend to
Learning and Teaching Committee the addition of a pathway leading to an MEng in
Innovative Manufacturing Technology for those students unable to obtain a
placement in industry, with effect from October 2009. (There would be no direct recruitment to this
new pathway.)
5. Change
to Programme Title
It was AGREED to recommend to
Learning and Teaching Committee the following change to a programme title
(effective date shown in brackets), subject to approval by Operations Committee
on 22 May:
MA/PGDip/PGCert Healthcare
Risk Management to MA/PGDip/PGCert
Patient Safety Management (September 2009 entry)
6. Discontinuation of Programmes
It was AGREED to recommend to
Learning and Teaching Committee discontinuation of the following programme
(proposed date of last intake shown in brackets):
BSc/BSc,DIS
Process Technology and Management (October 2009)
Author
– Jennie Elliott
Date
– May 2009
Copyright
© Loughborough University. All rights
reserved